This is one of just six examples of the Ferrari 250 GT Berlinetta Competizione that were built, a model perhaps best remembered today as the forerunner to the famous 250 GT Berlinetta Competizione “Tour de France.”
The Ferrari 250 model series were the vehicles that established the Italian automaker as a force to be reckoned with in the global sports and GT car market. The pace of development and innovation was rapid, culminating in cars like the 250 GTO, the 250 GT SWB, and the 250 LM.
Fast Facts – The Ferrari 250 GT Berlinetta Competizione
The Ferrari 250 GT Berlinetta Competizione is a highly sought after early GT car in the 250 GT series, just six were made and only three of those were designed by Pininfarina, like the car shown here.
The 250 GT Berlinetta Competizione was an evolutionary step between the Ferrari 250 MM and the Ferrari 250 GT Berlinetta “Tour de France” – a car that dominated the Tour de France Automobile from the mid-1950s through to the early 1960s.
The car you see here was restored by Ferrari in 1977 in Maranello, 22 years after it had first been built there, and today it carries Ferrari Classiche certification.
RM Sotheby’s are estimating that this car will sell for between $8,000,000 – $10,500,000 USD when it crosses the auction block with them on the 19th of November.
The Ferrari 250 GT Berlinetta Competizione
The pace of development for the Ferrari 250 series cars in the 1950s was remarkably swift, it mirrored much of what was happening in the world of Grand Prix racing as the engineers developed a better understanding of things like aerodynamics, suspension and braking systems, and of course, the engines themselves.
The cockpit has a classic, minimalist 1950s design with a wood-rimmed steering wheel framing the two key gauges – your speedometer and tachometer.
The development of the 250 GT Berlinetta Competizione built directly on the lessons Ferrari had learned building the 250 MM. That “MM” stands for “Mille Miglia,” a legendary race on open public roads that used to run between from Brescia to Rome and back starting in 1927 and ending in 1957.
The route was lined by up to five million spectators in later runnings of the event, it covered a distance of approximately 1,500 kms or 1,000 Roman miles. The name “Mille Miglia” means “Thousand Mile” in Italian.
Ferrari had made quite a name for themselves racing in the Mille Miglia, taking back-to-back victories in the event from 1948 until 1953, they would then win it again in 1956 with the Ferrari 290 MM Spyder Scaglietti.
The name “Berlinetta Competizione” translates directly as “Little Saloon Competition,” it essentially means that the car is a hardtop coupe designed for competition. Ferrari developed the 250 GT Berlinetta Competizione on the 250 Europa GT platform, a Tipo 508 chassis fitted with thew legendary Colombo-designed Tipo 112 V12 engine.
The 3.0 liter Tipo 112 V12 engine has single overhead cams per bank, two valves per cylinder, triple Weber 36 DCL carburetors, and a total power output of 230 bhp.
Just three examples of the six cars would be designed by Pininfarina, still known as Pinin Farina at this time as the name wasn’t formally joined in the middle until 1961.
Battista “Pinin” Farina and Enzo Ferrari had met just four years earlier in 1951, they opted to meet on neutral territory at a restaurant in the town of Tortona, exactly halfway between Turin and Modena. Neither man wanted to meet at the other’s headquarters.
Despite this cagey first meeting the two men formed an iron alliance, and Pininfarina developed the majority of Ferrari’s road cars for decades.
The Pininfarina-designed 250 GT Berlinetta Competizione saw the introduction of slightly better aerodynamics than its forebear, some of its design cues would also appear on exceedingly famous later Ferraris like the 250 GT SWB.
The 250 GT Berlinetta Competizione showed clear advancements in aerodynamics, many of which would be applied to later cars in the Ferrari 250 GT series.
The 1955 250 GT Berlinetta Competizione Shown Here
The car you see here has had a more interesting life than many, it was originally bought by Mr. Luigi Bertett, the then President of the Automobile Club of Milan. In 1964 it was shipped to a new owner in Athens, Greece however it was involved in a traffic accident a year later in 1965.
After its accident the car would sit in storage for 10 years until it was discovered by an American named Stephen Barney who was living in Rome. He rescued the car and had it sent to the Ferrari workshop in Modena, near where it had been made over 20 years earlier.
Once it was restored it was shipped across the Atlantic to the United States where Barney kept it in his “car barn” until it was bought by the collector Brian Brunkhorst in 1983. In the years since the car has belonged to collectors in Germany, Japan, and the United Kingdom.
The car is now due to roll across the auction block with RM Sotheby’s on the 19th of November, it has a price estimate of $8,000,000 – $10,500,000 USD and you can click here if you’d like to read more about it or register to bid.
At its debut at the 1959 New York Motor Show the Daimler “Dart” SP250 earned the unofficial title of being “The ugliest car of the show”. And to be sure the SP250’s looks are not its strong suit except for those of us with an eccentric sense of aesthetics.
These cars are rare, well designed, and hugely enjoyable to drive. The Daimler SP250 “Dart” might well be considered to be Britain’s “Corvette” it’s a car that delivers the traditional British Sports car driving experience on steroids, and for many it is superior to its peers for its quirky looks and unique all British V8 music-maker engine.
Fast Facts – The Daimler SP250 “Dart”
The Daimler SP250 has been called the “British Corvette” due to the fact it likely took the inspiration for its fiberglass body and V8 engine from the American sports car.
The quirky design of the SP250 has won it both fans and detractors in the decades since its introduction. The body was designed with aerodynamics in mind, however the front has been derisively been described as “droopy.”
The British police famously used SP250s to chase and catch the cafe racer “Ton Up Boys” in the 1950s and 1960s, none of the other police vehicles of the time could match the speed of the 100+ mph motorcycles.
Surviving examples of the Daimler SP250 have now become quite collectible, Jay Leno is a proud owner, and their prices seem to be steadily climbing in the classifieds and at auction.
In the Beginning
British car maker Daimler entered the 1950s as a company with an excellent past reputation, as an automaker favored by the British Royal Family, but as a company which was cash strapped and living in the doldrums of past glories.
It was a company that needed to pull a rabbit out of the hat in order to ensure not only its survival but its prosperity – and a V8 shaped rabbit seemed to be the perfect beating heart to install into a new range of car models with which to capture the imagination of not only British customers but – more importantly – a share in the booming United States automobile market.
Above Video: Jay Leno is doubtless the most famous fan of the SP250, in this video he tells the story of the car and there’s onboard driving footage with engine sound.
At that time Daimler was owned by the Birmingham Small Arms Company, an arms manufacturer which had made rifles for the British and colonial military and for civilian sporting shooters all over the world. This company is better known as “BSA” and remembered by many as a motorcycle manufacturer both of BSA and of Triumph bikes: BSA also owned Ariel motorcycles, Carbodies (who manufactured the iconic London taxi cabs), and prestige car maker Daimler.
Edward Turner, the creator of the Ariel Square Four engine and of the Triumph Speed Twin, became Chief Executive of the BSA group’s Automotive Division in 1956 and he was charged with the job of creating both a new V8 engine and cars to install them into. Turner had never designed a car before, and to assist him in this project was Jack Wickes, who had also never designed a car before, but there’s first time for everything.
Being the owner of a V8 Cadillac, Turner started his quest for design inspiration by studying the workshop manual and parts listing for a Cadillac V8 engine, and he had Jack Wickes do the same as they embarked on this new project. Their new design incorporated proven technology used in the Triumph and BSA motorcycle engines and it was intended that this new British V8 would power a four door saloon (sedan) which was designated the DN250, and a sports car which was called the SP250.
A British V8 to Upstage the Jaguar XK Six
The Daimler V8 engine that emerged from the work of the design team, who had been greatly assisted by Dr. J. N. H. Tait, was a five main bearing 90° V8 which featured a single chain-driven camshaft located high in the “V” of the engine actuating the valves by means of pushrods.
The block was of cast chrome-iron while the cylinder heads were of sand-cast high-tensile light alloy. The cylinder head design was loosely based on that of the Triumph Thunderbird motorcycle engines Turner had previously created, and incorporated part-hemispherical combustion chambers with two valves per cylinder, while pistons were aluminium alloy attached to steel connecting rods.
The 2.5 liter V8 has been lauded for its excellent engineering in the years since its production, and in later years it went on to power the Daimler 250 V8.
This all British V8 engine was made in two sizes: a 2.5 litre (2,548 cc) that weighed 419lb (190kg) dry, which was intended for both the DN250 sedan and the SP250 sports car; and a 4.5 litre which was physically slightly larger and weighed 498lb (226kg) dry which was intended for large Daimler limousines and which would compete against the Rolls-Royce V8 powered cars of the time.
So for Daimler the cars into which the smaller 2.5 litre V8 would be installed were intended to compete with the Jaguar cars installed with the much admired Jaguar XK six-cylinder engine.
The Daimler SP250 in Production
The Daimler SP250 was created on a bit of a “shoestring” budget – much in the same way that the Chevrolet Corvette was. The car was kept technologically conventional and used a body on chassis construction. The chassis was of a similar design to that used on the Triumph TR3 sports car, being a 14 gauge box section with central cruciform bracing.
This chassis seems to have been created with lightness in mind which on the original Daimler cars meant that it did not provide adequate stiffness, something that would be corrected on later models when the company was under Jaguar’s ownership.
This lack of rigidity gave the early SP250 the same teething problem as found on the early Chevrolet Corvettes – the doors could tend to come open while the cars were being driven. A problem not quite as dramatic as the passenger ejector seat fitted to James Bond’s Aston Martin DB5 in the movie “Goldfinger”, but still rather disconcerting – especially as the fault would tend to manifest itself when the car was being driven briskly.
To add insult to injury the bonnet (hood) could also pop open under the body flexing incurred during hard driving adding to the adrenaline rush of enthusiastic sports car driving in a not at all welcome way.
The interior of the car has all the classic styling cues of a British roadster from the era including more luxurious additions like wind up windows and a padded dashboard.
The suspension that formed part of this chassis incorporated an independent front with upper and lower arms, coil springs, and telescopic shock absorbers while at the rear were conventional semi-elliptic leaf springs with lever arm shock absorbers. The steering was by a cam and peg system which was and is not as good a choice as a proper rack and pinion.
The steering having no power assist it was heavy at parking speeds as one would expect regardless of whether it was cam and peg or rack and pinion. As originally fitted with a sensibly large steering wheel this heaviness poses no problem, and the older style larger steering wheel compliments the steering system giving a more precise feel in normal driving.
The brakes chosen for the SP250 were discs front and rear which was an excellent design choice. Disc brakes were only beginning to be used in passenger cars at that time and if they were used a typical setup was for discs at the front and drums at the rear. The four wheel disc brakes did not feature servo assistance, so although they provided efficient fade free braking the car requires the driver to have healthy leg muscles if an emergency stop was required.
In the 1950’s and into the 1960’s power brakes tended to lack feel and so were normally not preferred on sports cars: the absence of the power assist providing the driver with very direct feel for the brakes.
Daimler were on a tight budget in bringing the SP250 into production and their expectations had to be that the car would make relatively low production numbers. So, being in much the same situation as General Motors when they built the first Corvettes, Daimler decided to go with a fibreglass body just as Chevrolet had done. The tooling cost for fibreglass was one tenth the price compared with a steel body and it came with the added benefits of being light and rust free.
Daimler decided to christen their new sports car the “Daimler Dart” and that would be the name that would tend to stick to the car despite the fact that the car was forced to drop the name “Dart” at the time it made its 1959 American debut. US carmaker Dodge already had an established model named the “Dodge Dart” and they promptly took legal action to prevent Daimler using the “Dart” name.
Beauty is in the Eye of the Beholder
This car was to have almost a wedge shape with low front end and flowing lines up to the graceful rear fins, something which was probably intended for aerodynamic stability and to look attractive to Americans. Arguably the design achieved the desired aerodynamic effect, but the problem with the need for the car to be attractive to Americans is that the design team at Daimler were not able to come up with one.
What emerged as the production car was something that was either “love it” or ‘hate it”: with the vast majority of people on the “hate it” side. Just for the record I’m one of the few in the “love it” camp although I will still confess that the planned successor for the SP250 – the Sir William Lyons designed SP252 – was a far prettier car.
Early advertising for the SP250 showcased it as a fun young person’s care to rival the popular American Corvette.
Initially launched in the United States on 4th April 1959 as the “Daimler Dart” at the New York Motor Show it earned the dubious unofficial award for “Ugliest car of the show”. So it was pretty much received in the same way as the controversial Citroën DS when that car was first introduced.
The other aspect of the car which Americans decided was ugly was the name. Dodge already had a model called the “Dodge Dart” and so they objected to Daimler also using that name, with the result that Daimler simply re-named the car the Daimler SP250.
All that being said, the Daimler SP250 “Dart” has a purposeful, almost aggressive look, and it is aerodynamically sound with its low front end and semi-wedge shape providing a good down-force on the car, helping to make it stable at speed.
Production and Models
Production of the original Turner and Wickes designed Daimler SP250 began in 1959. In 1960 Daimler was purchased from the Birmingham Small Arms Company by Jaguar. Jaguar purchased the company primarily to acquire its manufacturing facility and skilled workforce to use to build Jaguars, although they continued production of Daimler cars.
Jaguar’s engineers assessed the SP250 as being in need of refining and in particular the chassis was subjected to significant modification to bring it up to Jaguar’s standard. The original 1959-1960 cars are now referred to as “A” specification or “A-Spec”.
The styling of the car is pure 1950s, with rear fins, plenty of chrome, and swooping lines.
Jaguar’s engineers assessed the SP250 as being in need of significant chassis stiffening. They had discovered that if they pressed down hard on the rear wing the car’s door gap could be made to grow by up to 8mm. Similarly the windscreen pillars could be made to flex an inch by hand pressure.
To rectify the car’s shortcomings Jaguar’s engineers fitted a steel box section hoop to connect the car’s “A” pillars together, added reinforcements to the “B” pillars, and installed two steel outrigger sill beams along each side of the chassis between the wheels, and other strategically placed strengthening reinforcements.
These things solved the impromptu door opening tendencies of the car while making it rather better to drive. These Jaguar improved cars are known as the “B” specification cars and were in production from 1960-1963. They were followed by the more luxuriously appointed “C” specification cars from 1963 until the end of production in 1964.
The three variants of the SP250 are subtly different. The “A” specification cars were not fitted with bumpers as standard equipment but instead at the front had chrome “whiskers” that extended from the grill, while at the back were two vertical bumper over-riders.
The “B” specification cars did not come with either whiskers at the front nor bumpers at the rear as standard, but like the “A” specification model could be ordered with bumpers as an optional extra. These cars featured an adjustable steering column. The “C” specification cars also did not come with bumpers as standard equipment but they featured a heater/demister, cigar lighter, and trickle charger.
The most famous SP250s were doubtless those used by the British Metropolitan Police for high speed pursuits during the early days of British motorways.
An interesting variant of the SP250 were the special order cars purchased by the London Metropolitan Police beginning in 1959. These cars were all painted black and were fitted with three speed automatic transmissions. Sports car enthusiasts might be horrified at the sacrilege of installing an automatic box in a sports car but the police were interested in practicality.
The automatic gearbox was not only easier for officers to use but it also protected the transmission and engine for day in day out fast acceleration needed to catch the motorcycle “Cafe Racer” boys who were essentially road racing on public roads, commonly on motorcycles designed by Edward Turner and Jack Wickes.
The SP250 was one of few cars that could actually catch up with them so they could be treated to a ticket to the “policeman’s ball” and perhaps helped to live a little longer – or at least keep a more watchful eye out for the little black Daimler sports cars.
Buying a Daimler SP250
Before launching into the purchase of a Daimler SP250 the best advice is to get connected with one of the owner’s clubs and do your research so you have a good working knowledge of the cars, and through the club members you obtain practical knowledge and a network of knowledgeable friends.
As you embark on your search for the right car scan the auction sites and classic car sales advertisements to get a feel for what you might expect to pay for cars in various levels of good preservation – or lack thereof. Consider not only your financial budget, but also you time budget in terms of how much time can you expect to invest in this car, especially if you are intending to purchase a “project” car. Many are those who purchase a project car to restore but who find they are unable to complete it.
As you begin to assess potential purchases remember that, although the body panels are made of fibreglass, that everything that holds that fibreglass in place – the car itself – is made of steel, and that steel was only subject to the rust proofing typical of many car makers of 50-60 years ago – remembering that back then we said that cars came “rust free” – i.e. the manufacturer gave you the rust for nothing. Also remember that some of that steel will be visible – and some not. That being said it is essential to do a lot of your assessment of a potential purchase from the underside of the car – get it up on a workshop stand so you can have a close look at the underside in undistracted comfort.
On the SP250 places to look for corrosion of the chassis are the front cross tube, front suspension turrets (replacements available but installation requires removal of the body shell), rear front spring hangars, outriggers, and rear suspension mounting points. Pay particular attention to the crossmember behind the rear axle and the reinforcing beams behind it; if repairs are needed it can be a complex task.
Mounting brackets for the lower front wishbones can show cracking of the welds. Repair of corrosion in the chassis may require the bodyshell to be removed which involves fifty sets of nuts and bolts to undo – almost certainly requiring liberal quantities of WD40 and possibly an occasional strategic whack with an impact driver.
Then there are the steel parts that were embedded into fibreglass panels to secure them to the chassis or other parts of the bodywork. In the nose section you will find two mounted either side of the radiator that secure the fibreglass to the front chassis tube. If these are corroded the nose will not be properly supported and when it flexes under load the bonnet/hood might just decide to jump up like Casper the Friendly Ghost and cause you a moment of memorable terror – because we all understand that what you can’t see can hurt you.
There are also embedded steel parts for the bonnet/hood catch, either side of the engine bay, seat runner fastening points, and B and C specification cars will also have embedded parts where the hoop brace at the “A” pillar passes through the fibreglass floor and attaches to the chassis outriggers.
The fibreglass itself might not rust but it can be subject to cracking especially in areas that have been subject to flexing, and areas subject to rough handling such as the boot/trunk lid having been carelessly slammed shut on a protruding piece of hard luggage – if some people will try to close a bursting suitcase by sitting on it then you can assume that there are those who might similarly try to sit on the fibreglass boot lid to force it to shut – and they will with near certainty not notice any damage done. Hopefully the car you are considering has not had such ministrations, but check thoroughly all over the body and underneath for sixty years worth of wear and tear.
The car makes use of a central-located rear fuel filler, so that owner’s could part with the fuel pump on either side of the car.
The suspension may show signs of wear in the trunnions – typically caused by lack of regular greasing. These can prove to be costly to repair.
Fibreglass might not rust like steel but it does tend to deteriorate with age like most plastics. It is possible to reinforce an old fibreglass body shell by applying new fibreglass underneath the original one to provide strengthening and support.
Checking the engine and transmission is much the same as for any classic car of the post war decades. The alloy heads make correct corrosion inhibitor a requirement and if the car has not had this maintained then cylinder head corrosion must be expected, signs of dirty white oil “mayonaisse” in the cooling system means trouble. Oil pressure should be 40psi at 30mph in top gear. These engines acquired a reputation for wearing in the heavier Daimler V8 250 but not usually in the lightweight SP250.
The gearbox was not a standard Triumph TR3 unit but was built specifically for the SP250. Despite that its crown wheel and pinion were not engineered fully up to the task of delivering V8 power to the back wheels when the driver decided to drive his sports car like a sports car.
Improving Your Daimler SP250
The original steering of the SP250 can definitely stand improvement and changing it over to a rack and pinion is a good way to accomplish that. The system from the Triumph Spitfire is the preferred unit. Beware of a car that has already had a conversion done to ensure it was done expertly. The steering is something that must not be compromised on, lives depend on it never failing. If you do choose to install a suitable rack and pinion system you will need to also install an electric radiator fan – which will also improve cooling efficiency nicely.
Installation of a servo assist for the brakes is another worthwhile improvement.
The rear lever arm shock absorbers can be replaced with telescopic ones, and such a conversion will improve the locating of the rear axle.
The original gearbox can have a traditional electric overdrive fitted and this makes highway speed cruising more pleasant and economical.
The fitting of an Austin-Healey 3000 diaphragm spring clutch will improve reliability and reduce the effort required to operate the clutch.
As mentioned previously, some of these cars were made with an automatic transmission, and the Jaguar made Daimler V8 250 was also offered with an automatic transmission. So if you prefer this it can be a good choice for your car – it is likely to improve reliability of the transmission which was one of the reasons the British police SP250’s were so fitted.
Daimler SP250 “Dart” Specifications
Chassis and Body: Box section 14 gauge steel ladder chassis with “X” cruciform central bracing. Design very similar to that used on the Triumph TR3. Fibreglass body over steel frame components, including steel parts embedded into the fibreglass body for mounting of bonnet (hood) attachments.
Suspension, Steering and Brakes: Front suspension fully independent by upper and lower “A” arms with coil springs and telescopic shock absorbers. Rear suspension by semi-elliptic leaf springs and lever arm shock absorbers. Steering by cam and peg. Brakes, hydraulic Girling discs front and rear. No power assistance on either steering or brakes.
Engine: 2.5 litre (2547cc) OHV V8 with two pushrod actuated valves per cylinder, these valves having double springs. Single dynamically balanced centrally mounted camshaft. Cast iron cylinder block, high tensile aluminium cylinder heads featuring hardened valves (making the engine suitable for use with unleaded fuel). Power 140bhp @ 5,800rpm, torque 155lb/ft @ 3,600rpm. Twin SU carburettors and SU electric fuel pump.
Pressurised cooling system with fan, thermostat and water pump.
Ignition by coil and distributor with automatic advance/retard.
Transmission: Four speed manual gearbox with synchromesh on top three gears, this gearbox being loosely based on the Triumph TR3 unit. Rear axle; hypoid bevel with ratio of 3.8:1.
Optional three speed automatic (originally not available except for the police specification cars and US export cars).
Performance: Standing to 60mph in 9.0 seconds. Top speed of 124mph.
Optional Equipment: The option list is quite extensive for the simple reason that when importing cars into the United States the standard equipment was taxed, whereas optional equipment was not. Options included heater/demister, windscreen washers, seat belts, bumpers for front and rear, hard top, fog lights, adjustable steering column (standard on B and C specification cars), wire wheels, whitewall tyres, electric overdrive.
Although controversial, the lines on the SP250 tend to grow on people over time, and the model now has established owner’s clubs in Britain and the United States.
Conclusion
The Daimler SP250 “Dart” is a car with a quite unique, albeit quirky, appearance. That being said it delivers a purist British sports car driving experience with an important something extra: that something extra being a genuine all British Edward Turner and Jack Wickes V8 engine thumping away as its beating heart. These are not a car for everyone, but if the SP250 has grabbed your attention then it is pretty certain that nothing less will do.
The unique nature of this car means that, despite them being quite rare, they are still able to be found for reasonable amounts of money. And if you are looking at purchasing one as a restoration project you can expect that once complete you should have a good investment quality car that will return to you the money and labour you’ve expended to restore it to its former glory – or better than its former glory.
These are one of the most desirable of all the British sports cars of the 1950’s and 1960’s, they ooze character, and accelerating hard that V8 will sing a song to send shivers up your spine.
When Aston Martin announced in 2018 that they would be bringing their most famous model back into limited production for the first time in over 55 years, the world’s motoring media almost exploded with excitement.
Adding to this excitement was the fact that these 25 official continuation cars were being built in direct collaboration with Albert R. Broccoli’s EON Productions as functional James Bond cars, with the gizmos and gadgets from the 007 film Goldfinger.
Fast Facts – The “Goldfinger” Aston Martin DB5
The Aston Martin DB5 from the film “Goldfinger”, with all of its secret modifications by Q Branch, is undoubtably one of the most famous cars in cinematic history.
The DB5 was a brand new production model in 1964 when the film was released, it led to a decades long affinity between the James Bond movie franchise and Aston Martin that continues to this day.
The Q Branch DB5 featured a range of offensive and defensive upgrades including machine guns, battering rams, a passenger ejector seat, a spinning tire slasher, a bulletproof rear shield, rotating license plates, a smoke screen, and an oil slick sprayer.
In 2018 Aston Martin announced a partnership with EON Productions to bring the DB5 back into production with the Q Branch 007 upgrades, each car cost £3.3 million pounds and just 25 were made.
Bringing Back The James Bond DB5
When the Aston Martin DB5 ceased production in 1965 it’s unlikely that anyone could have predicted that over 55 years later it would return to limited production, for just 25 additional units.
Above Video: Sean Connery as James Bond, being introduced to the original Q Branch Aston Martin DB5 in the film “Goldfinger.”
The DB5 Continuation series cars followed immediately in the footsteps of the 2017 Aston Martin DB4 GT Continuation – a limited production of just 25 cars at Aston’s Newport Pagnell facility.
The DB5 Continuation cars would be built using the same jigs as the original DB5, to the same specifications with one key difference – they would incorporate modifications by Oscar-winning Bond special effects supervisor Chris Corbould.
Corbould has worked on every Bond film since The Spy Who Loved Me, he’s worked on a vast array of films outside of the Bond universe, and he won the Oscar for Best Visual Effects at the 2011 Academy Awards for his work on the film Inception.
The “Goldfinger” Q Branch Gadgets
Developing versions of the gadgets from the Goldfinger DB5 that could actually be installed into a real, functioning DB5 proved a significant challenge, but Corbould managed it with the exception of one part – the passenger ejection seat.
There’s was just no way to do it legally, though the car does have the red button under the gear lever knob.
The interior of the car is largely the same as the standard DB5 with the exception of the radar tracker, and the flip-up arm rest that includes the controls for the car’s various weapons and gadgets.
Just as in the film, the 25 DB5 Continuation cars have the twin front machine guns behind the headlights, rotating number plates, smoke canisters, a rear oil slick sprayer, a pop-up bulletproof shield, battering rams front and back, and the rotating tire slasher that extends out of the centre of the rear wheels.
Special care was taken to ensure that all of the gadgets, which are controlled from an instrument panel hidden under the center armrest, are both functional and reliable – so they can be displayed for people time and time again without failing. Of course the machine guns aren’t live, they function by making the correct sound and powerful LEDs shoot red light out to simulate firing.
“The meticulous DB5 Goldfinger Continuation construction process – which takes around 4,500 hours per car – is undertaken at Aston Martin’s globally renowned Heritage Division headquarters in Newport Pagnell, Buckinghamshire.”
“Each of the 25 new cars is being built to the highest possible quality using a blend of Sir David Brown-era old world craftsmanship, with the sympathetic application of modern engineering advancements and performance enhancements, alongside the integration of cutting-edge gadgets developed in association with Chris Corbould OBE, the special effects supervisor who has worked on more than a dozen Bond films.” – Aston Martin
The 4.0 liter straight-six in the Continuation car is as immaculately presented as you may expect, it produces 290 bhp.
Under the hood you’ll find the same 4.0 liter Tadek Marek-designed straight-six as the original car, with double overhead cams and 12 valves, sending its 290 bhp through a ZF 5-speed gearbox to the rear wheels.
The Aston Martin DB5 “Goldfinger” Continuation Shown Here
The car you see here is one of the original 25 that were built and sold with an MSRP of £3.3 million pounds each, or approximately $4.4 million USD.
After this vehicle was built by Aston Martin it was delivered to its new owner in Saudi Arabia where it remains to this day. It’s now due to be offered for sale through Silverstone Auctions in Riyadh on the 25th of November.
The Volkswagen SP2 is a Brazilian-built sports car that was developed in the early 1970s, it entered production in 1973 and left production in 1976 after just 11,123 had been built.
Although it’s little-known outside of its native Brazil, the VW SP2 has become a cult classic in air-cooled car circles and they’re now highly sought after. Though relatively few have been exported.
Fast Facts – The Volkswagen SP2
The Volkswagen SP2 was developed in-house by Volkswagen do Brasil for the Brazilian market, which was starved for sports cars due to prohibitive import taxes on automobiles.
The development team was led by Senor Schiemann with designers Marcio Piancastelli, Jose Vicente Martins, and Jorge Oba.
The SP2 uses pre-existing VW mechanicals with a new steel body, and it has a rear-mounted 1.7 liter Volkswagen engine producing 75 hp and pushing the car to a claimed top speed of 100 mph.
Ultimately the SP2 wasn’t a success due to the fact it was underpowered for its weight. In more recent years owners have performed engine upgrades to increase power output by 200% or more, unleashing the potential of the car.
The Volkswagen SP2
In the early 1970s the best selling sports car in Brazil was the locally made Puma, a fiberglass-bodied vehicle that used VW Beetle running gear.
The interior of the SP2 was well-appointed for a Brazilian-made sports car of the time, considerably ahead of its competition.
Brazil had strict import taxes on vehicles at the time in an attempt to foster a stronger local automobile manufacturing sector, so the only real options for Brazilian sports car fans were low production volume vehicles like the Puma, Miura (not the Lamborghini), and the Santa Matilde.
It was likely the sales success of the Puma that set the ball in motion for the production of the SP1 and SP2, it was clear there was strong demand for a local sports car.
A team at the relatively autonomous Volkswagen do Brasil led by Senor Schiemann set to work on the project, using as many pre-existing VW parts as possible in order to keep development costs as low as possible.
They called it “Project X” and impressively they were able to go from prototype to production model in roughly two years. It’s clear that the SP vehicle series was intended for long term production as significant investments were made in steel stamping equipment for body panels.
With its rear-mounted air-cooled engine, sleek styling, and fastback rear the car has been compared with the Porsche 911 and 912.
Many parts for the SP1 and the SP2 were sourced from the Brazilian made Volkswagen Variant, including the distinctive headlights. Unlike the fiberglass-bodied Puma, the SP2 has a steel body and excellent fit and finish throughout, though this did result in the car being notably heavier.
Such is the popularity of the SP2 in Brazil that efforts have been made to bring the car back into production in redesigned form, though these plans are still on the drawing table at the time of writing.
Volkswagen SP2 – Specifications
The key difference between the SP1 and the SP2 was power output, the SP1 was fitted with a 65 hp engine and just 88 examples were ever built. It was intended to be the slightly less expensive model following the same formula as the Porsche 911 and Porsche 912 which had sold in parallel in Europe for a number of years.
Officially the names SP1 and SP2 stood for “Sao Paolo 1” and “Sao Paolo 2” however the cars were given the nickname “Sem Potência” shortly after the model’s release, meaning “Without Power” in Portuguese.
This nickname was given due to the fact that the 1.7 liter Volkswagen flat-four engine was producing just 75 hp, resulting in a 0 – 60 mph time of approximately 16 seconds, this was notably slower than the Puma, its arch rival.
The headlight assemblies were taken directly from the Volkswagen Variant, a Brazilian version of the Volkswagen Type 3.
Of course, the local tuning community wasted no time in setting to work on the cars, and in the years since there have been SP2s built with bored and stroked engines, higher compression ratios, hotter cams, and even turbocharging.
Unfortunately very little was done by Volkswagen’s Brazilian operation to fix the power issue when the car was in production, leading to a short 4 year production life with just over 11,000 built in total.
When the SP2 first entered production there was some pressure on Volkswagen to release a version of the car in Europe and other world markets. They opted not to do this, but they did sign an agreement with Porsche around the same time to develop a new VW sports car, this car would become the Porsche 924. A vehicle with a markedly similar side silhouette to its older Brazilian cousin.
Ultimately what could have been Brazil’s answer to the Porsche 911 failed due to its poor performance, that said, the car has become a cult classic in recent years, with owners applying modern performance parts to their engines to significantly increase power output and show what the cars are really capable of.
The 1.7 liter flat-four breathes through twin Solex 34 carburetors, power was a little on the low side with 75 bhp, however many owners have applied mods to boost output.
The 1974 Volkswagen SP2 Shown Here
The car you see here is a 1974 Volkswagen SP2, it was exported to Kuwait early in its life and possibly as a result of this it’s avoided the rust that plagued so many cars of this era.
In 2010 it was imported into the UK and it now benefits from a new VW Heritage SP2 1641cc engine fitted in 2018. This SP2 is one of just four believed to be on the road in the United Kingdom and one of every few shipped out of Brazil.
It’s clear that this car has never been restored and is in original condition throughout with some patina visible, particularly on the interior. It’ll be the new owner’s choice whether they undertake a full restoration, a more sympathetic cosmetic restoration, or simply keep the car as it is now.
It’s now due to roll across the auction block on the 17th of November with a price guide of £20,000 – £30,000, or approximately $26,900 – $40,400 USD. If you’d like to read more about it or register to bid you can click here to visit the listing.
This is the CCM Spitfire Cafe Racer, it’s a limited-production motorcycle, just 250 will be made by the decades-old British motorcycle marque Clews Competition Motorcycles.
In recent years CCM has made a name for themselves building ultra-lightweight motorcycles designed for blasting around canyon passes and British B-roads. The company’s bikes typically weigh less than 320 lbs, ands they’re fitted with a state-of-the-art engine, brakes, frame, and suspension.
Fast Facts – The CCM Spitfire Cafe Racer
The CCM Spitfire Cafe Racer was unveiled in 2019 as a limited edition production motorcycle that meets modern emissions regulations thanks to its fuel-injected 600cc Husqvarna-designed engine.
The CCM Spitfire model family is a return to classic British single-cylinder motorcycles, bikes like the BSA Gold Star, Velocette Venom, Matchless G50, AJS 7R, and of course the legendary Norton Manx.
The Cafe Racer variant of the Spitfire features classic cafe racer styling with low slung handlebars, a single seat with a rear cowl, and it’s all stripped back to keep weight as low as possible.
CCM have managed to keep the MSRP of the Spitfire Cafe Racer surprisingly affordable for a low-volume motorcycle of this type, selling for £9,274 ($12,460 USD) directly from the factory.
Clews Competition Motorcycles
Clews Competition Motorcycles, better known simply as CCM, was founded back in 1971 by the successful Trials and Scrambles rider Alan Clews.
Just 250 examples of the CCM Spitfire Cafe Racer will be built, this is bike number 24 from the first year of production.
Clews had made a name for himself as a racer however when the BSA Competition Department was disbanded in 1971 due to financial difficulties he saw an opportunity, and bought all of the factory equipment he could get his hands on.
Initially working out of his garage, Clews set about building 500cc four-stroke motocross and enduro machines that were capable of competing against the dominant two-stroke motorcycles of the time – a feat many considered impossible. Alan proved them wrong with a slew of top five finishes in international competition.
Over the intervening decades the company would build a variety of different motorcycles including the Armstrong MT500 for the military, the CCM GP450 which was a middle-weight adventure bike, and most recently the CCM Spitfire.
The company has no dealer network an all sales are handled directly out of the factory, allowing the buyer to form a direct connection with the people who will actually be building their machine.
The CCM Spitfire Cafe Racer
When it was released in 2019 the CCM Spitfire Cafe Racer caught the attention of the motorcycle world thanks to its combination of classic cafe racer styling cues combined with the scrambler DNA of the Spitfire model.
True to its name this model has a number of cafe racer styling cues including low slung handlebars, a single seat with a small rear cowl, and a low curb weight for sharp performance.
Like all of the motorcycles in the Spitfire model series, the Spitfire Cafe Racer has a hand-welded trellis frame made from high-strength T45 carbon steel that is finished with a clear coat to showcase the welds.
The 600cc Husqvarna-designed engine is a stressed chassis member and it includes a built in 6-speed transmission. It produces 55 bhp and 43 lb ft of torque at 5,500 rpm, it has a compression ratio of 12.0:1, a bore x stroke of 100 mm x 76.5 mm, it’s liquid cooled, and it has Mikuni D45 fuel injection.
The Spitfire Cafe Racer rides on modern suspension front and back consisting of fully adjustable upside down forks up front, with a fully adjustable monoshock in the rear. The bike is fitted with a 320mm wave disc up front with a four piston Brembo caliper, and in the rear there’s a 240 mm disc with a smaller two piston Brembo caliper.
With a curb weight of 142 kilograms, less than 320 lbs, the Cafe Racer is punchy, nimble, and devastatingly quick on the kind of curvy mountain roads it was designed for.
The 2019 CCM Spitfire Cafe Racer you see here is from the first year of production, it has just 541 miles on the odometer, it’s finished in gunmetal grey with a hand-stitched quilted leather seat, and it has the racing number 71 fixed to the side – a reference to the year CCM was founded.
This bike is currently being auctioned live by Collecting Cars, if you’d like to read more about it or register to bid you can click here to visit the listing.
